Numerical analysis of turbulent flow separation in a rectangular duct with a sharp 180‐degree turn by algebraic Reynolds stress model

Turbulent flow in a rectangular duct with a sharp 180‐degree turn is difficult to predict numerically because the flow behavior is influenced by several types of forces, including centrifugal force, pressure‐driven force, and shear stress generated by anisotropic turbulence. In particular, this type of flow is characterized by a large‐scale separated flow, and it is difficult to predict the reattachment point of a separated flow. Numerical analysis has been performed for a turbulent flow in a rectangular duct with a sharp 180‐degree turn using the algebraic Reynolds stress model. A boundary‐fitted coordinate system is introduced as a method for coordinate transformation to set the boundary conditions next to complicated shapes. The calculated results are compared with the experimental data, as measured by a laser‐Doppler anemometer, in order to examine the validity of the proposed numerical method and turbulent model. In addition, the possibility of improving the wall function method in the separated flow region is examined by replacing the log‐law velocity profile for a smooth wall with that for a rough wall. The analysis results indicated that the proposed algebraic Reynolds stress model can be used to reasonably predict the turbulent flow in a rectangular duct with a sharp 180‐degree turn. In particular, the calculated reattachment point of a separated flow, which is difficult to predict in a turbulent flow, agrees well with the experimental results. In addition, the calculation results suggest that the wall function method using the log‐law velocity profile for a rough wall over a separated flow region has some potential for improving the prediction accuracy. Copyright © 2007 John Wiley & Sons, Ltd.     

Burst-mode EDFA based on a mid-position gain flattening filter with an overpumping configuration for variable traffic conditions in a WDM environment

The WDM flatness easily collapses due to substantial changes in input power, an inherent problem in optical packet communication because of dynamic changes in traffic density. We propose a burst-mode EDFA with a novel configuration based on the concept of a mid-position gain flattening filter (GFF) with overpumping. This configuration can effectively suppress gain transience while maintaining WDM flatness.     

Delay-dependent and delay-independent stability criteria for a delay differential system

For a linear delay differential system with two coefficients and one delay, we establish some necessary and sufficient conditions on the asymptotic stability of the zero solution, which are composed of delay-dependent and delay-independent stability criteria. On the former criterion, the range of the delay is explicitly given.

     

Effects of OH concentration and temperature on NO emission characteristics of turbulent non-premixed CH4/NH3/air flames in a two-stage gas turbine like combustor at high pressure

This study examined the effects of OH concentration and temperature on the NO emission characteristics of turbulent, non-premixed methane (CH₄)/ammonia (NH₃)/air swirl flames in two-stage combustors at high pressure. Emission data were obtained using large-eddy simulations with a finite-rate chemistry method from model flames based on the energy fraction of NH₃ (E_NH3) in CH₄/NH₃ mixtures. Although NO emissions at the combustor exit were found to be significantly higher than those generated by CH₄/air and NH₃/air flames under both lean and stoichiometric primary zone conditions, these emissions could be lowered to approximately 300 ppm by employing far-rich equivalence ratios (?) of 1.3 to 1.4 in the primary zone. This effect was possibly due to the lower OH concentrations under far-rich conditions. An analysis of local flame characteristics using a newly developed mixture fraction equation for CH₄/NH₃/air flames indicated that the local temperature and NO and OH concentration distributions with local ? were qualitatively similar to those in NH₃/air flames. That is, the maximum local NO and OH concentrations appeared at local ? of 0.9, although the maximum temperature was observed at local ? of 1.0. Both the temperature and OH concentration were found to gradually decrease with the partial replacement of CH₄ with NH₃. Consequently, NO emissions from CH₄/NH₃ flames were maximized at E_NH3 in the range of 20% to 30%, after which the emissions decreased. Above 2100 K, the NO emissions from CH₄/NH₃ flames increased exponentially with temperature, which was not observed in NH₃/air flames because of the lower flame temperatures in the latter. But, the maximum NO concentration in CH₄/NH₃ flames was occurred at a temperature slightly below the maximum temperature, just as in NH₃/air flames. The apparent exponential increase in NO emissions from CH₄/NH₃ flames is attributed to a similar trend in the OH concentration at high temperatures.     

Influence of wall heat loss on the emission characteristics of premixed ammonia-air swirling flames interacting with the combustor wall

The influence of wall heat loss on the emission characteristics of ammonia-air swirling flames has been investigated employing Planar Laser-Induced Fluorescence imaging of OH radicals and Fourier Transform Infrared spectrometry of the exhaust gases in combustors with insulated and uninsulated walls over a range of equivalence ratios, ?, and pressures up to 0.5 MPa. Strong influence of wall heat loss on the flames led to quenching of the flame front near the combustor wall at 0.1 MPa, resulting in large unburned NH₃ emissions, and inhibited the stabilization of flames in the outer recirculating zone (ORZ). A decrease in heat loss effects with an increase in pressure promoted extension of the fuel-rich stabilization limit owing to increased recirculation of H₂ from NH₃ decomposition in the ORZ. The influence of wall heat loss resulted in emission trends that contradict already reported trends in literature. NO emissions were found to be substantially low while unburned NH₃ and N₂O emissions were high at fuel-lean conditions during single-stage combustion, with values such as 55 ppmv of NO, 580 ppmv of N₂O and 4457 ppmv of NH₃ at ? = 0.8. In addition, the response of the flame to wall heat loss as pressure increased was more important than the effects of pressure on fuel-NO emission, thereby leading to an increase in NO emission with pressure. It was found that a reduction in wall heat loss or a sufficiently long fluid residence time in the primary combustion zone is necessary for efficient control of NH₃ and N₂O emissions in two-stage rich-lean ammonia combustors, the latter being more effective for N₂O in addition to NO control. This study demonstrates that the influence of wall heat loss should not be ignored in emissions measurements in NH₃-air combustion, and also advances the understanding of previous studies on ammonia micro gas turbines.     

Coarse Metal Powder-Assisted pulsed CO2 Laser-induced Breakdown Spectroscopy for the Direct Determination of Heavy Metals in Soil

A novel method of laser-induced plasma spectroscopy utilizing a pulsed transversely excited atmospheric CO₂ laser has been developed for the high-sensitivity determination of heavy metals in soil. A coarse metal powder was used to trap the soil and to assist with plasma generation. When the CO₂ laser (10.6?µm, 1.5?J, 200?ns) was irradiated on the metal and soil powder, a high-temperature and long-lifetime luminous plasma was induced. Fine particles of soil were dissociated and were excited in the plasma region. The method was used for the rapid determination of Cr, Pb, and Hg in loam. The limits of detection for Cr, Pb, and Hg were approximately 0.8, 15, and 0.7?mg/kg, respectively.     

Ionic liquid salt bridge based on tributyl(2-methoxyethyl)phosphonium bis(pentafluoroethanesulfonyl)amide for stable liquid junction potentials in highly diluted aqueous electrolyte solutions

A moderately hydrophobic ionic liquid, tributyl(2-methoxyethyl)phosphonium bis(pentafluoroethanesulfonyl)amide ([TBMOEP⁺][C₂C₂N⁻]), shows a very stable liquid junction potential upon contact with an aqueous solution whose ionic strength is as low as 1 μmol dm⁻³. The stability with the maximum excursion of the potential within ±0.5 mV for 30 min is very promising for accurate determination of pH and other single ion activities potentiometrically.